M. Rouse, D. C. Jegley, D. M. Mcgowan, H. G. Bush, and W. A. Waters, Utilization of the Building-Block Approach in Structural Mechanics Research, vol.NASA, pp.105-116, 2005.

H. Hernández, F. Collombet, B. Douchin, D. Choqueuse, P. Davies et al., Entire lifetime monitoring of filament wound composite cylinders using Bragg grating sensors: II. Process Monitoring, Applied Composites Materials, vol.16, pp.197-209, 2009.

M. Mulle, R. Zitoune, and F. Collombet, Through-the-thickness material properties identification in a technological specimen using 3D-DIC and embedded FBG measurements, Experimental Mechanics, pp.1340-1343, 2008.

M. Mulle, R. Zitoune, F. Collombet, P. Olivier, and Y. H. Grunevald, Thermal expansion of carbon-epoxy laminates measured with embedded FBGS -Comparison with other experimental techniques and numerical simulation, Composites Part A, vol.38, pp.1414-1424, 2007.

J. P. Dunkers, J. L. Lenhart, S. R. Kueh, J. H. Van-zanten, S. G. Advani et al., Fiber optic flow and cure sensing for liquid composite molding, Optics and Lasers in Engineering, vol.35, pp.91-104, 2001.

C. Lekakou, S. Cooka, Y. Denga, T. W. Angb, and G. T. Reed, Optical fibre sensor for monitoring flow and resin curing in composites manufacturing, Composites Part A, vol.37, pp.934-938, 2006.

A. M. Grande, D. Landro, L. Bettini, P. Baldi, A. Sala et al., RTM process monitoring and strain acquisition by fibre optics, Procedia Engineering, vol.10, pp.3497-502, 2011.

G. Tuncol, M. Danisman, A. Kaynar, and E. M. Sozer, Constraints on monitoring resin flow in the resin transfer molding (RTM) process by using thermocouple sensors, Composites Part A, vol.38, pp.1363-1386, 2007.

V. Sobotka, N. Lefevre, Y. Jarny, and D. Delaunay, Inverse methodology to determine mold set-point temperature in resin transfer molding process, International Journal of Thermal Sciences, vol.49, pp.2138-2147, 2010.

D. Fratta, C. Klunker, F. Ermanni, and P. , A methodology for flow-front estimation in LCM processes based on pressure sensors, Composites Part A, vol.47, pp.1-11, 2013.

R. Matsuzaki, S. Kobayashi, A. Todoroki, and Y. Mizutani, Cross-sectional monitoring of resin impregnation using an area-sensor array in an RTM process, Composites Part A, vol.43, pp.695-702, 2012.

B. Yenilmez and E. M. Sozer, A grid of dielectric sensors to monitor mold filling and resin cure in resin transfer molding, Composites Part A, vol.40, pp.476-489, 2009.

D. Boll, K. Schubert, C. Brauner, and W. Lang, Miniaturized flexible interdigital sensor for In situ dielectric cure monitoring of composite materials, IEEE Sensors Journal, vol.14, issue.7, pp.2193-2197, 2014.

L. Khoun, R. D. De-oliveira, V. Michaud, and P. Hubert, Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites, Composites Part A, vol.42, pp.274-282, 2011.

K. Jung and T. J. Kang, Cure monitoring and internal strain measurement of 3-d hybrid braided composites using fiber Bragg grating sensor, Journal of Composite Materials, vol.41, pp.1499-1519, 2007.

M. Torres, F. Collombet, B. Douchin, L. Crouzeix, Y. H. Grunevald et al., Monitoring of the curing process of composite structures by tunnelling junction sensors, Sensors and Actuators A, vol.235, pp.256-264, 2015.
URL : https://hal.archives-ouvertes.fr/hal-01951237

M. Torres, R. A. Tellez, H. Hernández, and T. Camps, Mode I interlaminar fracture toughness of carbon-epoxy coupons with embedded ceramic sensors, Advances in Polymer Technology, vol.37, issue.6, pp.2294-2302, 2017.

F. Collombet, G. Luyckx, C. Sonnenfeld, Y. H. Grunevald, Y. Davila et al.,

J. Berghmans and F. , Cure monitoring of an autoclave manufactured industrial part: added value of complementary instrumentation, Proceedings of the 19th International Conference on Composite Materials (ICCM), 2013.
URL : https://hal.archives-ouvertes.fr/hal-02183204

M. Kobayashi and C. K. Jen, Piezoelectric thick bismuth titanate/PZT composite film transducers for smart NDE of metals, Smart Materials Structures, vol.13, pp.951-956, 2004.

M. Kobayashi, C. K. Jen, J. F. Bussiere, and K. T. Wu, High-temperature integrated and flexible ultrasonic transducers for non-destructive testing, NTD & E International, vol.42, pp.157-161, 2009.

E. Chehura, C. C. Ye, S. E. Staines, S. W. James, and R. P. Tatam, Characterization of the response of fibre Bragg gratings fabricated in stress and geometrically induced high birefringence fibres to temperature and transverse load, Smart Materials and Structures, vol.13, pp.888-895, 2004.

O. Frazao, J. Carvalho, L. Ferreira, F. Araujo, and J. L. Santos, Discrimination of strain and temperature using Bragg gratings in microstructured and standard optical fibres, Measurement Science and Technology, vol.16, pp.2109-2113, 2005.

G. Luyckx, E. Voet, W. De-waele, and J. Degrieck, Multi-axial strain transfer from laminated CFRP composites to embedded Bragg sensor: I. Parametric study, Smart Materials and Structures, vol.19, pp.1-9, 2010.

E. Voet, G. Luyckx, W. De-waele, and J. Degrieck, Multi-axial strain transfer from laminated CFRP composites to embedded Bragg sensor: II. Experimental validation, Smart Materials and Structures, vol.19, pp.10-18, 2010.

T. Geernaert, M. Becker, P. Mergo, T. Nasilowski, J. Wojcik et al., Bragg grating inscription in GeO2-doped microstructured optical fibers, Journal of Lightwave Technology, vol.28, pp.1459-1467, 2010.

N. Lammens, D. Kinet, K. Chah, G. Luyckx, C. Caucheteur et al., Residual strain monitoring of out-of-autoclave cured parts by use of polarization dependent loss measurements in embedded optical fiber Bragg gratings, Composites Part A, vol.52, pp.38-44, 2013.

C. Sonnenfeld, G. Luyckx, F. Collombet, Y. H. Grunevald, B. Douchin et al., Cure cycle monitoring of laminated carbon fiber-reinforced plastic by fiber Bragg gratings in micro-structured optical fiber, Proceedings of the 19th International Conference on Composite Materials (ICCM), 2013.

C. Sonnenfeld, G. Luyckx, F. Collombet, Y. H. Grunevald, B. Douchin et al., Embedded fiber Bragg gratings in photonic crystal fiber for cure cycle monitoring of carbon fiber-reinforced polymer materials. Micro-structured and Specialty Optical Fibres II, vol.877500, 2013.
URL : https://hal.archives-ouvertes.fr/hal-02181537

S. Kim, H. Murayama, K. Kageyama, K. Uzawa, and M. Kanai, Study on the curing process for carbon/epoxy composites to reduce thermal residual stress, Composites Part A: Applied Science and Manufacturing, vol.43, issue.8, pp.1197-1202, 2012.

Z. Guiming, W. Jihui, N. Aiqing, and L. Shuxin, Process-induced residual stress of variablestiffness composite laminates during cure, Composite Structures, vol.204, pp.12-21, 2018.

S. Lu, D. Chen, X. Wang, J. Shao, K. Ma et al., Real-time cure behaviour monitoring of polymer composites using a highly flexible and sensitive CNT bucky paper sensor, Composite Sciences and Technology, vol.152, pp.181-189, 2017.

W. Ya, Y. Wang, P. Zhang, F. Liu, and S. Luo, Laser-induced freestanding graphene papers: A new route of scalable fabrication with tunable morphologies and properties for multifunctional devices and structures, Small, p.1802350, 2018.

S. Luo, Y. Wang, G. Wang, K. Wang, Z. Wang et al., CNT enabled co-braided smart fabrics: A new route for non-invasive, highly sensitive & large-area monitoring of composites, Scientific Reports, issue.7, p.44056, 2017.

M. A. Ali, R. Umer, K. A. Khan, Y. A. Samad, K. Liao et al., Graphene coated piezoresistive fabrics for liquid composite molding process monitoring, Composites Science and Technology, vol.148, pp.106-114, 2017.

P. Van-velthem, W. Ballout, D. Dumont, D. Daoust, M. Sclavons et al., Phenoxy nanocomposite carriers for delivery of nanofillers in epoxy matrix for resin transfer molding (RTM)-manufactured composites, Composites Part A, vol.76, pp.82-91, 2015.

S. M. Doshi and E. T. Thostenson, Self-sensing carbon nanotube composites: processing and characterization, Multifunctionality of Polymer Composites: Challenges and New Solutions, vol.25, pp.752-784, 2015.

L. Tzounis, M. Zappalorto, F. Panozzo, K. Tsirka, L. Maragoni et al., Highly conductive ultra-sensitive SWCNT-coated glass fiber reinforcements for laminate composites structural health monitoring, Composites Part B, vol.169, pp.37-44, 2019.

L. Sida, W. Guantao, W. Yong, X. Ye, and L. Yun, Carbon nanomaterials enabled fiber sensors: A structure-oriented strategy for highly sensitive and versatile in situ monitoring of composite curing process, Composites Part B: Engineering, vol.166, pp.645-652, 2019.

M. Torres, Parameters' monitoring and in-situ instrumentation for resin transfer moulding: A review, Composites Part A, vol.124, p.105500, 2019.

M. Torres, L. Crouzeix, F. Collombet, B. Douchin, and Y. H. Grunevald, Assessments on the mechanical behaviour of a monolithic composite structure instrumented with a monitoring patch, Journal of Composite Materials, vol.51, pp.3597-3610, 2017.
URL : https://hal.archives-ouvertes.fr/hal-01943028

M. Torres, L. Crouzeix, F. Collombet, B. Douchin, and Y. Grunevald, Numerical and experimental value added of multi-instrumented technological evaluator for the analysis of thick monolithic composite structures with singularity details, Composite Structures, vol.127, pp.41-50, 2015.
URL : https://hal.archives-ouvertes.fr/hal-01951238

Y. H. Grunevald, Value Added of MITE toolbox on development of a full composite railway bogie, comparison with a classical approach, Proceedings of the 7 th International Conference on Rapid Product Development, 2009.